check engine RENAULT SCENIC 2007 J84 / 2.G Anti Lock Braking System Bosch 8.0 ESP Workshop Manual

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 12V2 MR-372-J84-38C050$310_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
SETTINGS
VP001: Write VIN.
This command permits manual entry of the vehicle's VIN into the computer. Use this command
each time the computer is replaced. The VIN number (VF...) can be found on the manufacturer's
plate on the front right-hand door pillar and on the body panel under the left-hand side of the
windscreen.
VP004: Vehicle parameters.
This command is used to configure the engine type + braking definition + body type.
Select command VP004 on the diagnostic tool (the parameters selected must correspond with
the vehicle type).
VP006: Write last After-Sales operation date.
The date of the operation must be entered whenever the ESP system is worked on in the
workshop. Select command VP006 on the diagnostic tool.
Enter the operation date with the tool keyboard.
VP007: Tachometric index.
This command is used to program the computer memory with the index required to calculate
vehicle speed from the speed at which the wheels turn.
The Bosch 8.0 ESP computer transmits the vehicle speed signal to all areas where this signal is
needed (instrument panel, engine management, etc.). This vehicle speed signal replaces the one
supplied by the speed sensor located on the gearbox.
The ESP computer calculates the vehicle speed from the wheel speed and the tyre
circumference.
Note:
The vehicle speed is conveyed by wire (track 33) to the xenon bulbs, radio and electric sunroof,
and by the multiplex network to the other computers.
The tyre circumference must be programmed into the memory of a new computer. This consists
of entering an index X using the diagnostic tool and command VP007 Tachometric index.
Once the index has been entered using the VP007 command, clear the computer fault memory
and then switch off the ignition. Use the PR030 parameter to check that the index has been stored
correctly.
MR-372-J84-38C050$310_eng.mif

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 15V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
DF001
PRESENT
OR
STOREDCOMPUTER SUPPLY VOLTAGE
1.DEF : below minimum threshold
2.DEF : above maximum threshold
3.DEF : abnormal voltage
NOTESSpecial notes:
The fault appears during a road test at a vehicle speed of > 6 mph (10 km/h). The
computer signals an external supply fault.
Conditions for applying the fault finding procedure to stored faults:
Apply the fault finding procedure whether the fault is present or stored.
Check the condition and connection of the battery terminals.
Check the condition and position of the ABS/ESP fuses in the engine fuse and relay box.
Check the 50A power fuse in position 5 on the power fuse board.
Check fuse F13 (25A) on the UPC and the correct locking of the grey 4-track PPH1 connector (Vdiag 44) or
the 25A fuse F8 on the UPC and the correct locking of the black 6-track CM connector (Vdiag 48).
Check the connection and condition of the tab 1 red wire of the grey connector.
Check the connections on the ABS/ESP computer 46-track connector.
Check the ABS earths on tracks 1 and 4 (mounted under the ABS/ESP unit) and visually inspect all the
ABS/ESP wiring.
Check the continuity between the fuses and tracks 2 and 3 of the computer connector (+ before ignition feed on
the tracks) and between the UCH and track 28 of the computer (+ after ignition feed on the track).
Clear the computer fault memory. Switch off the ignition.
Switch on the ignition again and carry out a new check using the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF001 /ESPBOSCH_V09_DF001/ESPBOSCH_V0A_DF001/
ESPBOSCH_V0B_DF001 /ESPBOSCH_V11_DF001/ESPBOSCH_V12_DF001
MR-372-J84-38C050$434_eng.mif

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 25V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF017
PRESENT
OR
STOREDCOMPUTER
1.DEF : power supply fault or internal electronic malfunction
2.DEF : programming / initialisation invalid
NOTESSpecial notes:
The voltage displayed in the parameter (PR005) is the + after ignition feed voltage
of the computer and not the hydraulic unit power feed.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed > 36 mph (60 km/h).
1.DEF
NOTESNone
Check the condition and connection of the battery terminals.
Check the condition and position of the ABS/ESP fuses in the engine fuse and relay box.
Check the 50A power fuse in position 5 on the power fuse board.
Check the 25A fuse F13 on the UPC and the correct locking of the grey 4-track PPH1 connector (Vdiag 44) or
the 25A fuse F8 on the UPC and the correct locking of the black 6-track CM connector (Vdiag 48).
Check the connection and condition of the tab 1 red wire of the grey connector.
Check the connections on the ABS/ESP computer 46-track connector.
Check the ABS earths on tracks 1 and 4 (mounted under the ABS/ESP unit) and visually inspect all the
ABS/ESP wiring.
Check the continuity between the fuses and tracks 2 and 3 of the computer connector (+ before ignition feed
on the tracks) and between the UCH and track 28 of the computer (+ after ignition feed on the track).
Clear the computer fault memory. Switch off the ignition.
Switch on the ignition again and carry out a new check using the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF017 /ESPBOSCH_V09_DF017/ESPBOSCH_V0A_DF017/
ESPBOSCH_V0B_DF017 /ESPBOSCH_V11_DF017/ESPBOSCH_V12_DF017

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 27V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF020
PRESENT
TACHOMETRIC INDEX PROGRAMMING
NOTESSpecial notes: ABS warning light flashing at 8 Hz out of fault finding mode.
The Bosch 8.0 ESP computer transmits the vehicle speed signal to all areas where this signal is needed
(instrument panel, engine management, etc.).
This vehicle speed signal replaces the one supplied by the speed sensor located on the gearbox. The ESP
computer calculates the vehicle speed from the wheel speed and the tyre circumference.
Note:
The vehicle speed is conveyed by wire (track 33) to the xenon bulbs, radio and electric sunroof, and by the
multiplex network to the other computers.
The tyre circumference must be programmed into the memory of a new computer. This consists of
entering an X index using the diagnostic tool and the command VP007 Tachometric index.
Once the index has been entered using command VP007 Tachometric index, clear the computer fault memory
and then switch off the ignition. Use parameter PR030 Tachometric index to check that the index entered is being
used correctly by the system.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF020P/ESPBOSCH_V09_DF020P/ESPBOSCH_V0A_DF020P/
ESPBOSCH_V0B_DF020P/ESPBOSCH_V11_DF020P/ESPBOSCH_V12_DF020P

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 39V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF066
PRESENT
OR
STOREDINJECTION MULTIPLEX SIGNAL ABSENT
NOTESSpecial notes:
Although the fault is stored in the computer, it is not caused by ABS/ESP components,
but it indicates that the ESP is deactivated due to an injection frame transmission fault.
Run fault finding on the injection system.
Note:
The injection does not always store these transient faults as quickly as the ABS/ESP
system. If no fault is stored in the injection computer, start the engine; if there is no fault
present, contact the Techline.
Once the fault in the injection system has been repaired, clear the ABS/ESP computer
fault memory.
The injection multiplex signal is transmitted to the ABS/ESP computer via the
Protection and Switching Unit.
Priorities when dealing with a number of faults:
Deal with faults DF152 and DF153 first, whether they are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started up.
Check the condition and correct locking of the blue PEH connector of the UPC (Vdiag 44) or the grey CT1
connector of the UPC (Vdiag 48 or higher).
Carry out a multiplex network test and check the injection system with the diagnostic tool. If the fault is still
present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF066 /ESPBOSCH_V09_DF066/ESPBOSCH_V0A_DF066/
ESPBOSCH_V0B_DF066 /ESPBOSCH_V11_DF066/ESPBOSCH_V12_DF066

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 0A, 0B, 11, 1238C
38C - 44V2 MR-372-J84-38C050$434_eng.mif
*USM: NO
BOSCH 8.0 ESP
Vdiag No.: 0A, 0B, 11,
12
DF097
PRESENT
OR
STOREDNO AUTOMATIC TRANSMISSION MULTIPLEX SIGNAL
Vdiag: 0A, 0B, 11, 12
NOTESSpecial notes:
Although it is stored in the computer, this fault does not cause the warning lights to
come on or generate a fault message, because the ABS/ESP system is not faulty. Run
fault finding on the automatic transmission with the diagnostic tool.
Note:
When the fault in the automatic transmission system is repaired, clear the ABS/ESP
fault memory.
The multiplex signal from the automatic transmission is sent to the ABS/ESP via the
Protection and Switching Unit.
Priorities when dealing with a number of faults:
Deal with faults DF152 and DF153 first, whether they are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started up.
Using the diagnostic tool, check in the parameter screen that the PR063 "Vehicle parameters" truly correspond
with the vehicle undergoing fault finding.
Is PR063 Vehicle Parameters correct?
YES
Check the condition and correct locking of the blue PEH connector on the UPC
(Vdiag 44) or the grey CT1 connector on the USM* (Vdiag 48).
Carry out a multiplex network test.
If the fault is still present, run fault finding on the automatic transmission gearbox and
repair as necessary.
If the fault is still present, contact the Techline.
Use command VP004 Vehicle parameters to define the appropriate parameters for the
vehicle type.
Clear the computer fault memory.
Exit fault finding mode, switch off the ignition and carry out a new test with the diagnostic
tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V0A_DF097 / ESPBOSCH_V0B_DF097/
ESPBOSCH_V11_DF097/ESPBOSCH_V12_DF097

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 45V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
DF126
PRESENT
OR
STOREDCOMBINED SENSOR SIGNAL PLAUSIBILITY
NOTESSpecial notes:
This fault means that the combined sensor signals are not consistent with the other
ESP sensors (steering wheel angle sensor and wheel speed sensors). If the fault
appears while the vehicle is being driven on a steep gradient, during a very tight turn
or while the vehicle is being transported on a lorry, train, boat, etc., with the engine
running, clear the fault and if possible check that the fault has disappeared by carrying
out a road test.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test.
Check the connection and condition of the combined sensor connector.
Ensure that the sensor is properly fixed to the body in the right direction (arrow pointing to the front of the vehicle).
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of the
tyres.
Using the diagnostic tool, calibrate the steering wheel angle in the "Electric power steering" subgroup followed by
command RZ003 "ESP sensor programming" for Vdiag 09, 0A, 0B, 12 and 11 in the ABS/ESP.
Re-establish dialogue with the ABS/ESP computer, clear the computer fault memory, carry out a road test then
check again with the diagnostic tool.
If the fault is still present, adjust the axle assembly geometries. Adjust if necessary and use the diagnostic tool to
calibrate the steering wheel angle again in the "Electric power steering" subgroup, then run command RZ003 ESP
sensor programming for Vdiag 09, 0A, 0B, 12 and 11 in the ABS/ESP.
Carry out a road test.
If the fault is still present, replace the sensor.
AFTER REPAIRClear the computer fault memory. If the combined sensor has been replaced, erase the
ESP sensor programming (Vdiag 09, 0A, 0B and 11) with command RZ003 ESP
sensor programming.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF126 /ESPBOSCH_V09_DF126/ESPBOSCH_V0A_DF126/
ESPBOSCH_V0B_DF126 /ESPBOSCH_V11_DF126/ESPBOSCH_V12_DF126
MR-372-J84-38C050$496_eng.mif

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 48V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF186
PRESENT
OR
STOREDINSTRUMENT PANEL MULTIPLEX SIGNAL ABSENT
NOTESSpecial notes:
Even though it is stored in the computer, this fault does not cause the warning lights to
come on or a fault message. Using the diagnostic tool, run fault finding on the
instrument panel.
Note:
Once the fault in the instrument panel system has been remedied, clear the ABS/ESP
computer fault memory.
The multiplex signal from the instrument panel is sent to the ABS/ESP via the
Protection and Switching Unit.
Priorities when dealing with a number of faults:
Deal with faults DF152 and DF153 first, whether they are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started up.
Check the condition and correct locking of the blue PEH connector of the UPC (Vdiag 44) or the grey CT1
connector of the UPC (Vdiag 48 or higher).
Carry out a multiplex network test.
If the fault is still present, perform fault finding on the instrument panel and repair accordingly.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF186 /ESPBOSCH_V09_DF186/ESPBOSCH_V0A_DF186/
ESPBOSCH_V0B_DF186 /ESPBOSCH_V11_DF186/ESPBOSCH_V12_DF186

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 54V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF193
PRESENT
OR
STOREDINVALID INJECTION MULTIPLEX SIGNALS
NOTESSpecial notes:
Although it is stored in the computer, the ABS/ESP system is not faulty. The ESP is
deactivated due to unusable information from the injection system. Perform fault
finding on the injection system using the diagnostic tool.
Note:
The injection does not always store these transient faults as quickly as the ABS/ESP
system.
If no fault is stored in the injection computer, start the engine; if there is no fault present,
contact the Techline. Once the fault in the injection system has been repaired, clear
the ABS/ESP computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after starting the engine.
Carry out a multiplex network test and check the injection system with the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF193 /ESPBOSCH_V09_DF193/ESPBOSCH_V0A_DF193/
ESPBOSCH_V0B_DF193 /ESPBOSCH_V11_DF193/ESPBOSCH_V12_DF193

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 55V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF194
PRESENT
OR
STOREDELECTRIC POWER ASSISTED STEERING MULTIPLEX SIGNALS
INVALID
1.DEF : inconsistency
2.DEF : fault detected
NOTESSpecial notes:
Although it is stored in the computer, the ABS/ESP system is not faulty. The ESP is
deactivated due to unusable information from the electric power steering system. Run
fault finding on the electric power steering with the diagnostic tool.
Note:
The electric power steering does not always store these transient faults as quickly as
the ABS/ESP system.
If no fault is stored in the electric power steering computer memory, start the engine; if
no present fault is displayed, contact the Techline. Once the fault in the electric power
steering system has been repaired, clear the ABS/ESP computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after starting the engine.
1.DEF
NOTESNone
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of
the tyres.
Check the axle assemblies, adjust if necessary.
Calibrate the steering wheel angle in the electric power-assisted steering using the diagnostic tool.
Ensure that the combined sensor is properly fixed to the body in the right direction (arrow towards the front of
the vehicle).
If all the checks are OK, clear the computer fault memory and clear the ESP sensor programming (Vdiag 09, 0A,
0B, 12 and 11) using command RZ003 "ESP sensor programming".
Carry out a road test.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF194 /ESPBOSCH_V09_DF194/ESPBOSCH_V0A_DF194/
ESPBOSCH_V0B_DF194 /ESPBOSCH_V11_DF194/ESPBOSCH_V12_DF194